Home> Industry Information> Rice Harvester Maintenance Instructions

Rice Harvester Maintenance Instructions

July 14, 2018


Correct technical maintenance is an important condition for preventing the failure of combine harvester and ensuring high-quality, high-efficiency, low-consumption and safe work, and must be carried out in time and carefully according to the maintenance content specified below.

Important:

For maintenance, please use the regular parts provided by the Company.Using of similar parts in the market will affect the performance of the machine and reduce the service life.

1, the whole machine clean. Clean the surface of the machine and drain the water in the tank. Then open the inspection hole cover in various parts of the machine, remove the protective cover, and remove the remaining rice grains in the parts such as the drum room, intermediate conveying device, threshing device, and pull-out device. , Straw, soil, oil and other debris, remove debris remaining in the moving plate, cleaning room, inside and outside of the fan volute, gearbox, header, and other parts. After cleaning, the machine was started and the working parts were kept at high speed for 5 minutes to discharge the remaining contents of the machine. Then rinse the outside of the machine with water and start the machine at high speed for 5 minutes to remove the remaining water.



2, transmission maintenance. Remove all the triangular tapes, wipe them, and then hang them. Carefully remove the chain and put it in diesel to clean it. Apply oil or butter and put it in a dry and ventilated place.

3, check the wear parts. Check the wear-resistant parts of the machine and replace the worn-out connecting rod, knife, etc. in time. First move and set the knife apart. Remove debris, weeds, and other debris attached to the knife and check whether the riveting of the blade is loose or not, whether the wear is excessive or not, and whether the knife bar is deformed. If the looseness is to be caulked, replace it if worn excessively, if the knife bar is deformed. To correct. Then it is reinstalled according to the requirements. After the restoration, the clearance of the blade shall be within 0.2mm, and the movable cutter bar shall be smooth and smooth without any stagnation, and then oiled and rusted.

4, the whole machine lubrication. Check the lubrication area of the machine and re-fill all the lubricating parts with grease, especially moving parts such as traveling mechanism and transmission, add butter to each bearing, and apply grease or grease to friction parts to prevent corrosion. Then use the small and medium throttle to keep the engine idle for 5 to 10 minutes.

5. Check the threshing roller and fasteners. Replace the overweight threshing arches and correct the lateral changes of the arches. Check the fasteners. If any fasteners are found to have come off or become loose, they should be promptly replaced and tightened.

6, transmission system inspection. Remove the drive chains and clean them. Check for cracks in the chains and if any problems are found, replace them in time. Remove all the drive belts and check if any slippage, burns, deterioration or damage occurred due to long use time. Replace them if any. The drive belt that can be used continuously should be cleaned and dusted with talcum powder. After installing the drive chain and belt in position, start the machine at high speed for 2 to 3 minutes.

7, the whole storage. Clean up the metal stripping on all surfaces of the machine and apply paint to prevent rust. Raise the harvester with wood or bricks to allow the crawler to leave the ground and relax all the tensioning components. Lift the plunger rod and retract it into the cylinder, lower the header, pull the picker wheel, and place it on the pad. The harvester should be stored in a ventilated, dry and flat room with dust-proof cloth. The engine is started twice a month, idling the diesel engine at medium speed for 10 minutes.

The above is the Rice Harvester Maintenance Instructions we have listed for you. You can submit the following form to obtain more industry information we provide for you.

You can visit our website or contact us, and we will provide the latest consultation and solutions

Share to:

Send Inquiry

Home> Industry Information> Rice Harvester Maintenance Instructions
Related Products List

Home

Product

Whatsapp

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send